Aluminum Extended Magazine Plate for GLOCK™ G17 (9mm) / G22 (.40 cal) & EMP Pocket Clip Combo

NOTES:
- Clip placement location is viewed left or right from the back side of the magazine. Example: if you want bullets facing forward and magazine in left hand pocket, pick RIGHT side EMP Clip.
- See PRODUCT SPEC for set screw application

Aluminum Extended Magazine Plate for GLOCK™ G17 (9mm) / G22 (.40 cal):
: The Strike Industries Aluminum Extended Magazine Plate for GLOCK™ G17 (9mm) / G22 (.40 cal) was designed to provide smoother magazine reloading through a slow drag / no snag design while maintaining maximum magazine capacity. Machined from 6061-T6 aluminum, this Extended Magazine Plate (EMP) adds plus 5 9mm or plus 4 .40 cal rounds to compatible OEM double stack GLOCK™ magazines. Following the success of our EMP systems for pistols, the form factor and unique geometric design gives a unified and aggressive aesthetic look to your GLOCK™ G17. Included is an aluminum plate which adds extra locking security. Give your GLOCK™ pistol the extra rounds it deserves with the Strike Industries Aluminum Extended Magazine Plate (EMP) for GLOCK™ G17 (9mm).

Package Contents:
-x1 Aluminum Extended Magazine Plate for GLOCK™ G17 (9mm) / G22 (.40 cal)
-x1 Extended length spring
-x1 Aluminum locking plate
-x1 Aluminum locking plate set screw (M3x8mm)
-x1 Hex tool [2mm]
-x1 Warning card

Product Features:
-Machined from 6061-T6 aluminum
-Plus 5 round capacity for 9mm
-Plus 4 round capacity for .40 cal
-Includes aluminum locking plate
-Low drag / no snag design
-Fits USPSA 140mm race division limit
-Available in anodized SI BLACKLINE, REDLINE or FDELINE colors

DISCLAIMER:
-Due to numerous factors that take place during the anodization process, the color lines from batch to batch of a certain product may vary
-Threaded holes located on EMP are anodizing blind holes and may not be completely covered with coating

WARNING:
-DO NOT OVERTIGHTEN set screw when installing the aluminum locking plate. If you are unsure, please contact our customer support team or consult with your local gunsmith.
-SI aluminum EMP was intentionally designed to be a tight fit and can damage the polymer magazine body base ears. Must be installed by a certified gunsmith only.
-Use of small c-clamp (or similar tool) to gently and lightly squeeze the bottom middle of the magazine body just above the plastic locking ears where the SI aluminum EMP attaches to the magazine. Just enough so the SI aluminum EMP will slide in or out. Be careful not to bend the OEM magazine body metal liner and remove the c-clamp (or similar tool) as soon as the SI aluminum EMP is installed or removed. C-clamp or similar tool may mar/scratch magazine body surface. Please be careful and use a material to protect the magazine body surface.

EMP Pocket Clip:
The Strike Industries EMP Pocket Clip gives you a quick and easy way to carry a spare pistol magazine for when you need it. The clip can also help hang or organize magazines in a range bag or safe. Offered for either right or left handed shooters, or however you prefer your bullet facing orientation, this SK-5 carbon steel matte black finish low-profile pocket clip is made to only work with compatible Strike Industries Extended Magazine Plate’s (EMP). This pocket clip attaches directly to compatible SI EMP's to ensure a fast draw with no fuss. Your spare magazine sits where you need it without fishing around in your pocket. With a simple pull, the magazine is in your hand to get you back in the fight. The SI EMP Pocket Clip includes everything you need along with various length set screws (x4) so you can adapt to all compatible Strike EMP's currently offered or any EMP developed in the future. With this new low-budget option, make sure the Strike Industries EMP Pocket Clip is part of your Everyday Carry (EDC) so do not leave home without it.

Package Contents:
-x1 EMP Pocket Clip (right or left)
-x1 Set screw (M4x4mm Socket)
-x1 Set screw (M4x5mm Rounded)
-x1 Set screw (M4x6mm Rounded)
-x1 Set screw (M4x8mm Rounded)
-x1 Hex tool [2,5mm]
-x1 Hex tool [3mm]

Product Features:
- Direct mount to compatible SI Extended Magazine Plate (EMP)
- Available for right or left handed shooters
- Included set screws for variety of SI EMP fitments
- Low-profile
- Matte black finish
- SK-5 carbon steel

Product Specs:
LENGTH: 45.65mm (1.80")
WIDTH: 29.25mm (1.15")
HEIGHT: 36.34mm (1.43")
WEIGHT: 1.50 oz
WEIGHT W/ PKG: 2.40 oz

EMP Pocket Clip:
-LENGTH: 28.67mm (1.13")
-WIDTH: 25.00mm (0.98")
-HEIGHT: 26.87mm (1.06")
-WEIGHT: 2.0 oz
-WEIGHT W/ PKG: 3.0 oz

SET SCREW APPLICATION:
-GLOCK™: G19/G17/G22 (M4x5mm)

COMPATIBILITY (Pocket Clip): With SI Magwell for GLOCK™ 17/22/31/34/35/45
COMPATIBILITY (EMP):
-GLOCK™ factory OEM G17/G17L/G19X/G22/G24/G34/G35/G45 double stack magazines
SI EMP Pocket Clip
-Magwell: tested to work with SI Magwell
NOT COMPATIBLE:
-10-round magazines
-ETS Magazines

NOTE: Not for sale to California, New York and New Jersey residents due to 10-round state laws. The checkout process will show NO shipping method available.

It is the responsibility of the customer to know and abide with local gun laws.

DISCLAIMER:
-This product is not manufactured, authorized, endorsed, or warranted by GLOCK. GLOCK does not warrant or represent that this product is compatible with GLOCK pistols.
--“GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. and GLOCK Ges.m.b.H. Neither Strike Industries Inc. nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to advertise the sale of GLOCK pistols, parts, or components. For additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and parts visit www.glock.com.

-CALIFORNIA PROPOSITION 65 WARNING:-
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov